| Page properties | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| ||||||||||
|
Devices compatible with Mitsubishi FX3USNP protocol.
- Name: SNP
- Version: 1.0.10.0
- Protocol: Proprietary
- Interface: Standard Serial Port
- Runtime: Multiplatform.Net 4.8 (Windows)
- Configuration:
- Devices / Protocols
| Table of Contents | ||||||
|---|---|---|---|---|---|---|
|
Overview
Communication with devices compatible with Mitsubishi FX3U
Supported Operands
SNP protocol.
Communication Driver Information | |
|---|---|
Driver name | Snp |
Assembly Name | T.ProtocolDriver.Snp |
Assembly Version | 1.0 |
Available for Linux | False |
PLC types supported | GE Fanuc PLCs - 90/30 and 90/70 Series, PACSystem and VersaMax. |
Interface | Serial and MultiSerial |
SNP (Series Ninety Protocol) was created by GE Fanuc Automation (GE + Fanuc). Later the brand became GE Intelligent Platforms, and today the PLC line (PACSystems/VersaMax) is with Emerson.
Supported Operands
AI | Analog Input |
AQ | Analog Output |
G | Discrete Global Memory |
I | Discrete Input |
Q | Discrete Output |
T | Output (Temporary) Coils |
M | Internal Coils |
S | System Status |
R | Register Memory |
Operand
Read
Write
Data Type
Address size
D - Data register
Yes
Yes
Word
2 bytes
TN – Timer Current value
Yes
Yes
Word
2 bytes
TS – Timer Contact
Yes
No
Bit
1 bit
CN – Counter Current value
Yes
Yes
Word
2 bytes
CS – Counter Contact
Yes
No
Bit
1 bit
X - Input relay
Yes
No
Bit
1 bit
Y - Output relay
Yes
Yes
Bit
1 bit
M - Internal relay
Yes
Yes
Bit
1 bit
S0 - Annunciator
Yes
Yes
Bit
Channels Configuration
Protocol Options
- Maximum size of blocksBlockSize: Defines the maximum of addresses in a read block.
Protocol Options
- Com – Define the Port of communication
- Baud Rate – Define the rate at which information is transferred in a communication channel.
- Databits – Define the number of data bits in each character
- Parity – Define the method of detecting errors in transmission.
- Stop bits – Define the stop bits.
- DTR – Define a control signal in RS-232 serial communication.
- RTS – Define the Request to Send
- CTS – Define the Clear to Send
- CtsWait – Time in milliseconds
Nodes Configuration
Primary Station
- amount of items per group, the default value is 1000.
- PLC Type: 90/30 or 90/70.
- Level 2 password: PLC write access authentication password.
Settings
- Serial and MultiSerial channels:
Default configuration:
DataBits: 8.
StopBits: 1 if parity is used, 2 if no parity.
Set the other fields according to your Serial or MultiSerial port configuration.
Nodes Configuration
Station Configuration
SlaveId: Set this field with the address of the slave device in the SNP network. They can be addressed from 1 to 247 for serial nodes, or 0 to 255 for TCP/IP nodes. The address 0 is used for the broadcast.
- Serial channels:
Station syntax: <SlaveId>
Ex: 1
- MultiSerial channels:
Station syntax: <ComPort>;<SlaveId>
Where : <ComPort> = COM Port of the slave device in the SNP network (default is com1).
Ex: com1;1
Points Configuration
The syntax for the Mitsubishi FX Serial SNP communication points isare: <Operand> <Address>Where :
- %<Operand><Address>
- <Operand>: Represents the Device Memory :
- <Address>: Address number
Operand |
|---|
D - Data register |
TN – Timer Current value |
TS – Timer Contact |
CN – Counter Current value |
CS – Counter Contact |
X - Input relay |
Y - Output relay |
M - Internal relay |
S0 - Annunciator |
Note: The Y Operand is an Octal Numeral System.
Operand: Indicates the memory area, the valid values are:
AI | Analog Input |
AQ | Analog Output |
G | Discrete Global Memory |
I | Discrete Input |
Q | Discrete Output |
T | Output (Temporary) Coils |
M | Internal Coils |
S | System Status |
R | Register Memory |
Address: Indicates the data address in the memory area.
Ex: %R00001 (Operand = R, Address = 1)
Driver Revision History
SNP Driver |
|---|
Driver Revision History
Revision History | |
|---|---|
Version | Notes |
1.0. | |
0.0 | Initial release on new documentation standards |
In this section...
| Page Tree | ||
|---|---|---|
|